Vehicles
Sections
139 not categorized PORSCHE 924 GT ID PLATECan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 914 1970-76 (includes uncategorized and accessory items) AAA01 Show your friends where you shop or service your Porsche! Inexpensively and easily add some style and status to your Porsche. General FitmentACCESSORY
$1.06
Make a selection ER911MNT If you need more front camber adjustment range, these elephant racing offset camberplates are for you. the monoball and mounting holes are offset, allowing up to 3/4 degree of additional camber adjustment range. just the ticket for your race car. These plates use the same spherical bearing technology as our front monoball cartridges and replace the entire factor camberplate. For even more negative camber, combine with our de-cambered ball joints. Combine with polybronze control arm bearings to achieve a rigid front suspension geometry that maintains alignment under hard braking and cornering loads. General Fitment914 1970-76
$499.00
Make a selection BK5652 By stephan wilkinson. Wilkinson's spunky and entertaining memoir is a yarn-spinning and wise-cracking romp over the author's many occupations, hobbies, blunders and idiosyncrasies. In a quest to restore a well-used ‘83 911 ends two years and $60,000 later with a car worth far more in hard-earned experience than blue-book value. General FitmentACCESSORY
$75.00
Make a selection FVD33300905 This rear spring plate is manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. New rs spec. (85 shore) rubber bushings are installed to make this a direct bolt on. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Features: made from ¼ inch spring steel includes new rs spec. (85 shore) rubber bushings made in Germany sold individually. 2 necessary per car.
$273.90
Make a selection FVD33300902AT Send us your original spring plate and we will have it reconditioned for you. The reconditioning process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and media blast the part. Once fully prepared, we install new rs spec. (85 shore) rubber bushings/bearings. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Then we seal the spring plate with a corrosion resistant plating. Sold individually. 2 necessary per car. Please note: this only fits cars with the g50 transmission.
$261.80
Make a selection FVD33391100SET Replace worn-out original spring plate bushings to return your car to its intended ride quality and performance. This is a high-quality OEM 65 shore density bushing set, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. This set is a direct replacement for original part # 911 333 009 00 sold as a set. 1 necessary per axle.
$108.90
Make a selection FVD721805000 Aligns the drill bit when removing broken studs.
$491.70
Make a selection FVD343997PSS
$893.46
Make a selection FVD53191101 As a striker plate ages, it will start to rattle and can potentially be a safety risk. Repair it with this high-quality replacement sourced in Germany. We recommend adding new striker plates gaskets, either 90153170323 or 90153170324 depending on what thickness you need. If new screws are necessary use part # 99921900800 sold individually. One kit is required per striker plate.
$44.00
Make a selection FVD721VW402
$127.60
Make a selection KEV503032001
$127.60
Make a selection N0147032 Known as: pan-head screw / pan-head screw m 6 x 18 View/Change Diagram
From $3.72
Make a selection KEV503031001
$127.60
Make a selection FVD116802 The reinforced sachs performance pressure plate (clutch cover) has fundamental advantages against a genuine pressure plate, such as a higher transmittable torque and higher resistance against thrust. It also allows for faster and sportier gearshifts. That makes it extremely useful for street tuning, endurance races and hill climbing. The sachs performance clutches are assembled by hand. This guarantees the highest quality attributes in clamping load and release characteristics. Features: higher transmittable torque. Higher clamping load. Less abrasion. Direct replacement for the oe pressure plate. 225 mm. Max torque: 413 lb/ft (560 nm) * *dependent on the type of disc material being used with this pressure plat...(choose a part on the right to read more) General Fitment914 1970-76911 1970-73
From $907.21
Make a selection NLA11601400 Â for adapting later engines to 356a transmissions with unguided throwout bearings Â
$110.79
Make a selection
$1.49
Make a selection
$6.33
Make a selection
$46.48
Make a selection
$7.65
Make a selection NLA72355305 Two required per vehicle replaces 64472355305
$7.85
Make a selection
$322.73
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |